Room Overview & Circuit Strategy
The entire bedroom is placed on its own dedicated circuit, with a single breaker feeding the ceiling fan, light, and all receptacles. This makes it easy to kill power to the whole room for future work.
First, we install the 2-gang switch box.
- Height: Mark the stud at 4 feet; set the top of the box at that mark.
- Location: Place on the doorknob side of the door.
- Flange: The tabs on the box butt against the stud, providing a 1⁄2-inch setback for drywall.
Ceiling Fan Box Installation
Use a saddle box for ceiling fans or heavy light fixtures.
- Centering: Locate the room’s center. Ideally, this lands on a rafter; otherwise, install a wood block between rafters to mount the saddle.
- Mounting: Remove the center screw, position the saddle over the rafter, mark holes, and drive the two provided screws. The larger lag bolts are used later when the fan is hung.
- Wire: Run 12/3 Romex (black for light, red for fan, white neutral, bare ground) from the switch box to the saddle box.
Drilling & Running 12/3
- Drill size: Use a 1⁄2-inch bit for 12/3; a 3⁄8-inch bit for 12/2.
- Route: Drill up through the top plate, then from the saddle box to the switch box.
- Unspool neatly: Pull wire off the spool and flatten it before running to avoid kinks.
- Length: Leave about 5 inches of wire out of each box.
The 6/12 Rule for Outlet Spacing
This rule dictates receptacle placement per electrical code:
- 12-foot max: No point along a wall may be more than 12 feet from an outlet.
- 6-foot rule: An outlet must be within 6 feet of a door (on each side) and within **6 feet of any corner.
- Short walls: Any wall 2 feet or longer requires a receptacle.
Example: An 11-foot-6 wall with a 4-foot door needs one outlet in the center (5 feet 9 inches from both the corner and the door).
For additional guidance on receptacle placement in other areas of the home, see Essential Guidelines for Kitchen Socket Placement.
Outlet Box Placement
- Height: Measure 18 inches from the floor.
- Mark: Draw an “X” on the side of the stud.
- Install: Nail the single-gang box so its top aligns with the mark, and the flanges sit tight against the stud.
Drilling Holes & Running Wire
Drilling Through Studs
- Height: Drill holes at 24 inches above the floor for straight, consistent runs.
- Centering: Drill through the center of the stud.
- Windows: Raise the drill height to about 16 inches when passing near windows.
- Tight spots: Use a right-angle drill attachment for tight spaces like next to windows.
Running 12/2 Wire for Receptacles
- Connect the switch box (power source) to the first receptacle, then daisy-chain from outlet to outlet.
- Around doors: Drill up into the rafter space and come back down on the opposite side of the doorway.
Pro Tip for Corners: Pre-bend the wire into a hook shape (about a 45° angle) to help it navigate around corners.
Stapling & Securing
- Staple size: 1⁄2-inch staples for 12/2; 3⁄4-inch for 12/3.
- Code requirements:
- Staple within 6 inches of every box.
- Staple every 4 feet along the run.
- Method: Pull wire taut to the middle of the stud before stapling.
Understanding the broader code framework can help ensure your work is compliant. Review Building Codes 101: Zoning, Occupancy Groups & Construction Types Explained for more context.
Wiring Connections
Grounding with Crimp Sleeves (Stay-Comps)
- Strip the jacket off both cables entering the box.
- Strip 1⁄2 inch of insulation from each conductor.
- Push both bare copper ground wires through a single copper crimp sleeve.
- Smash the sleeve with pliers to secure the wires together.
- Cut one wire shorter, then twist the two into one solid ground.
- Push the connection back into the box (it will be connected to the device later).
For a refresher on the fundamentals behind these connections, consult Engineering Circuit Analysis: Voltage, Current, and Resistance Basics.
Final Walkthrough
- Power comes from the panel box to the switch box.
- From the switch, 12/3 runs up to the ceiling fan/light combo.
- From the same switch, 12/2 runs to the first receptacle, then daisy-chains around the room to all other outlets.
- All boxes are stapled and labeled for easy identification after drywall.
Note: The panel cover is off because it is actively being wired, this is normal during installation.
If you are preparing for a career in this field, explore Mastering Your Electrician Interview: Tips and Strategies for guidance on landing your first job.
this video i'm going to show you how to install rough end electrical in a new construction house and the room i'm
standing in right now i'm going to show you a to z on how to do the outlets the light the ceiling fan all that and if
you're new to this channel my name is josh it's all about building your house so be sure to subscribe ring that bell
so you get a notification or time release new video and hammer that like button for me that's all i ask in return
for making this video so we got a lot to do today so let's get started when i go to wire my own house i like to put each
bedroom on its own circuit and what i mean by its own circuit is it's going to have a breaker and a home run right to
the panel box so that way that one breaker powers that whole bedroom so if you need to shut the power off to that
bedroom you just hit that breaker and it kills the power to the lights the receptacles and everything so the first
thing i'm going to do is put up the switch box because the switch box is going to be used for the ceiling fan and
the light and that's going to be where the power comes in as well so this is a two gang box and what i mean by two gang
box there is a place for two switches or two receptacles for that matter if you need to but this is gonna be for
switches in this case so i'm gonna show you the height in which to put switches there's really no exact height in which
to set a switch box but i always like to go ahead and mark four foot on the stud that's gonna be
anchored to and then i either set the whole house and this is up to you you either set it
at the top of that four foot mark at the center or place it at the bottom so i like to just go ahead and put that right
at the top it gives you a nice precise area to go by and if you notice these notches here or not really notches but
these like flanges what this does i'll show you up close is that butts right against the stud and what that does is
gives you a half inch so a place for your drywall to um go around so by the time you
install the drywall it's going to be flush with this uh double gang box here and in order to anchor it you just drive
these nails in all right and that baby is not going anywhere and as far as the placement of
this you always place it on the door knob side of the door so if the door swings in like this you want to just
reach in and kick the switch on the light up the room which i figured you'd probably assume that but i just want to
make that clear all right so now that we have this mounted we know our power is going to be coming into this box okay so
we're not going to do that right now but it that means that's going to be what powers our lighting fan so what i'm
going to do is get some 12 3 wire and run it up to a ceiling fan mount and i'll show you how to do that i'm going
to use this product called the saddle box and it's for ceiling fans or any light fixtures or any hanging light
anything like that that's going to have some weight to it and i'll put a link to my amazon store in the description below
if you want to check these out if you do purchase it i do get a small commission because i'm an affiliate but there's no
extra cost to you to do that but these things are phenomenal and the reason why
is the design of them it just saddles right over your rafter or your floor joist if it's a two story if it would go
right over it and that's what mounts the ceiling fan to hold that weight so it's a great invention so first thing i do is
find the center of the room and mount this into place so if you look here there's a little screw in the center and
these two larger screws so you just mount it with these for now and then after the drywall's up and you hang your
fan or light then you use these bigger lag bolts so for now we're going to find the center
and then we're going to mount it so to do this just take the little screw out of the center
and then place it on an impact driver or a drill and i marked the center of the room right here and i just so happen to
be sitting on an actual rafter but here's the thing if there's not a center rafter like there is in this instance
would you get very lucky if that happens what you what i would had to done is put a block
in this space here between the rafters and then that would have been what this saddles onto so if it was in between the
rafter it'd go over the block like this but i got really lucky here this never happens by the way but
in this case it did so you just put it up where it goes now that we have the saddle box sitting
in the center all we got to do is reinstall the little screw through the hole you got it from
and we're done so the what holds the weight is those lag bolts once you go to install your actual ceiling fan so
that's for another video so be sure to subscribe for that so now i'm going to run 12 3 wire up to this saddle box and
to that switch to get that 12 3 wire over to that saddle box i got to drill up through this plate of the wall
and since i'm doing a 12-3 wire meaning there's three 12 wires in one wire which i'll show you that in a minute i'm going
to use a half inch drill bit and i use a 3 8 drill bit when i'm doing 12 2 wire which there's only two wires in the one
wire okay so since i'm doing 12 3 half inch and then i go to the stud in which the box is
anchored to for our switches then i drill right up through and make sure you stay in the center of the wall
boom right like that now i'm just going to run it right from that switch box over to that saddle box so what i like
to do is unravel the wire as it comes out of the spool so that way it's nice and flat
by the time it gets to where you need to go because if you pull it straight out of
this spool it's going to be all twisted and we don't want that so now as you can see it's nice and flattened out
[Music] so now when i get over here to the switch box i just take it wrap it around
hold about five inches out of the box then take a pair of wire cutters just cut it off there
and this stuff is kind of stout and now what you need to do is go ahead and put it into the switch
box and always push the backs of these out a little bit before i run a wire in them
okay and now i'm going to slide it into place
and i'm not going to staple this yet because i got some more wires coming into this switch box now it's time to
start placing the single gang electrical boxes around a room for your outlets before i do that i want to explain to
you what the 612 rule is so i want to go to the whiteboard and draw a diagram of it because it's way easier to explain
because when it comes to outlet spacing is very important for code let's go over it before i go over the 612 rule on the
whiteboard behind me i just want to disclose that i am not an electrician i just learned all this from trial and
error from building my own houses throughout time and i had an inspector explain the 612 rule to me a while ago
and it stuck with me so i wanted to spread it to all you guys that may find benefit in it and again go with your
local building codes don't go off something you see on youtube let's get to it so this diagram is probably the
easiest way to understand the 612 rule for outlets so it more or less means 12 foot is the
max distance between outlets on a wall and 6 foot means that's how far you need to be
from a door there needs to be one outlet at least six foot from the door on each side so as you can see here here's a
four foot door in the middle of this 11 foot six wall okay so it's only less than four foot on each
one of these walls so if the wall is over two foot it needs to have a receptacle on it so you'd have to put
one right here and right here somewhere in between this wall and the door needs to have a receptacle and the same goes
that for here so if it's ever two foot you need to have a receptacle on it and another reason for the six foot means
from each corner it can't be no more than six foot so as you can see here we're just at the maximum distance from
that corner to the six foot and in between we have six foot here and from this corner to this outlet is six foot
and as you can see that wall is 18 foot long so that is within code so this is the max distance of 12 foot refers to
this wall down here so from the corner of this wall to this first outlet we got five foot so that's within code and then
from this outlet to this outlet it's over six foot it's eight foot so we can have up to 12 foot so it can't be longer
than 12 foot so we're eight foot so that's within code and we're within five foot
from this corner to this outlet so that's good to go so if we look at this 11 foot six wall this wall only needs
one right in the center because as you can see here it's five foot nine from the corner to the outlet so that is less
than six foot so that meets code so that's good and as you can see this whole room would meet code alright let's
get back to physically installing these outlets [Music]
[Applause] [Music] [Applause]
[Music] [Applause] let me explain to you what i just did
there so what i did i measured up off the floor 18 inches where i figured there is going to be a receptacle and
then i put an x on the side of the stud so it's easily visible and then i went through and just dropped a receptacle
box electrical box whatever you want to call it next to the floor beside where it's going and then i'm just going to go
ahead and anchor that right to that mark the top of this outlet box is going to be
right there then all you got to do is drop the nails in on the side to anchor it just like did the switchbox and it's
going to be spaced out a half inch all right so just like this guys line it up to that mark hold those
flanges tight against the stud and then just take a hammer and then drive those nails in
now it's time to drill holes all through the studs to connect all the outlets together
and what i like to do is i'm a little ocd i like to keep my wires running straight
so what i do i pull up from the floor two foot and it's just the easy measurement to
remember so i'll go ahead and drill right in the center of that two by four stud or two by six depending on what you
constructed with right through that mark but in the center of the stud
now i go through and mark the studs as i go and keep on drilling
[Applause] [Music] i'm here at the window and obviously we
can't continue the 24 inch measurement so i come up around 16 inches on these five foot windows and it seems to be
pretty comfortable but i just wanted to point out to you whenever you have a tight space like this a right angle
drill of some kind is definitely going to be your best friend this is a job max with the wrangle drill attachment
and how it works you just simply slide into the space and drill it out now it's time to start running some wire
to each one of those outlets i'm going to be using 12 2 wire and 12 2 is heavier than the 14 too you'll see a lot
of people using but i just like to use a little heavier gauge because it can handle a little more load than the 14 2
wire even though it's overkill i just feel better about it so first thing i'm going to do is unspool a bunch of this
wire because i gotta be able to go around this whole room and then i'm gonna go ahead and go from this outlet
up to the switch first because that's gonna be the power to energize all these receptacles
[Music] [Applause] [Music]
[Applause] just come up into the switch box first thing
and then i want to make sure it's enough to be able to staple this at least four to six inches from this switch
and then we're going to come over come down come down loop around the receptacle box
now it's the length i'm going to go ahead and cut that right there using a pair of wire cutters
and then we're going to push it through into the outlet box now our power going to our receptacles
is ran from the switch and now we need to go to the next outlet so i got the end of the wire and i'm
going to have to go around the doorway so i'm going to have to drill up into the rafter space and come back down on
the other side of the doorway [Music] these are half inch staples that are
used for 12 2 wire you'll have to get three quarter inch staples for 12 3 wire that we ran earlier
so now what we do pull those wires to about the middle of that stud and you gotta stay within six inches
and staple it of that receptacle so that way it will pass code and check your local
building codes to see what you need to do but here it's within six inches now every four foot i'm going to place a
wire staple to meet the requirements here
so this is 12 3 wire right here so we got a red for the fan power and then we got the black for the light power and
then we got the neutral which is white then we got the copper which is for ground then this is the 12 2 wire here
this one has just one black for the receptacles and that's just the power of those and then you got your
bare copper which is where the ground and got the white that's for the neutral i just wanted to show you guys the
difference between 12 2 and 12 3. all right as you can see the power that's going to be coming to the switch box
runs down here to this receptacle first and it's going to come back up and continue running
up over this door opening here and down to this next receptacle so now all we got to do is continue that sequence to
each one of these receptacles until we end at this one [Music]
[Applause] [Music] all right i want to show you guys a
little pro tip when you get to a corner like this where you got to come in and then come out this side so you got to
make a 45 degree angle what i like to do is take the wire and go ahead and pre-bend it
something like that so you kind of have a hook on it and then just fish it in like that and
see if you can get it to hit that hole and that's definitely the easiest way i've found to try to push these wires
through all right so there we go
and uh i used to not do it that way and it was always a pain until i figured out the arc now we got to tie these
wires together and to do that simply go ahead and take the sheathing off the wire itself so all you got to do is take
a utility knife and lightly go over the jacket and then just spread back the casing
like so reach up in the box go ahead and cut that off any paper that's on there be sure to get
that off too and then do that to the other wire and this stuff like i said is very very
pliable so it cuts easy and go ahead and separate all those like so
and now all we got to do is strip these wires i got a pair of these wire strippers they're really easy to use
i'll put a link to my amazon store where you can purchase these anyways you just slide that over that wire
you want to leave about half inch go ahead and strip all those
and these things work so slick all right now
so we want our black and whites over to the side the copper wires are what we're going to be addressing
we want to use these copper crimp sleeves and they're also called stay combs
but they're really easy to use all you got to do is take the little copper sleeve slide it over both of the grounds
like so and then after you do that you want to take a pair of pliers
and just smash that crimp ring down like so okay and then go ahead and twist
you'll form one solid copper wire you don't have to twist it super tight where you break it but it's nice and snug
and then bend one to the side and always cut a little shorter so it didn't so
um obvious and then just take that and bend it to the side you'll have this little piece of copper left and then
smash it together there this ground is all tied together with a single wire now and then shove all these
back in the box and then you'll hook that to the outlet or the receptacle whatever you want to
call it whenever the time comes shove them in the box and we will address that after the drywall is hung
now all i got to do now is take this 12 2 wire and run it from this switch box over
to this panel box in order to get there i just got to run the cable all the way up into the attic space and down to the
panel box [Music] this is our power coming from the panel
box this is going up the ceiling fan and light combo and then this is the receptacles their
continued power so now we're just going to line all those up and go ahead and take a wire staple
and then staple those in place and this is a three-quarter inch staple since we got a 12 3 wire we're dealing with i'm
going to show you how to tile these wires together in another video so what i do so i know what they are
when i go to time together after the drywall's up i go ahead and label them now
so i know this one was the power coming from the panel box
and this wire here is the continued power but i'm going to put
receptacles just to make it simple to remember then the 12 3 wire is a given it's the fan and light
combo but i'll go ahead and do that anyways for
demonstration purposes and now what we do we're just going to roll those back into
the box until the drywall is hung all right one final walkthrough powers to the switch
going up to our ceiling fan light combo that's going to be operated off a switch so we're going to have a light here fan
here and then the power is going to tie into that switch box and continue to all the receptacles around the room
using the 612 rule and everything looks good and we're all stapled off and there is nothing wrong
with this job looking very nice before everybody gets in an uproar in the comments about this panel box cover
being off and how unsafe it is it's because it's actively being installed i'm actually going to be making a how to
install a panel box video and i'll be installing this bedroom we just wired up so be sure to subscribe so you get a
notification when i release that video and that's all i got for you today guys and again be sure to ring that bell so
you get the notification i'll see you in the next video have a good one
A dedicated circuit provides independent control for the entire room, making it easier to shut off power during maintenance or emergencies. This setup also prevents tripping breakers from high-wattage devices in other rooms and simplifies troubleshooting future electrical issues.
First, locate the room’s center and ensure it aligns with a rafter or install a wood block between rafters for mounting. Remove the saddle box’s center screw, position it over the rafter, mark the screw holes, then drive the two provided screws. The larger lag bolts are used when hanging the fan itself. Always run 12/3 Romex (black for light, red for fan, white neutral, bare ground) from the switch box to the saddle box.
The rule ensures no point along a wall is more than 12 feet from an outlet, and outlets must be within 6 feet of any door (on each side) and any corner. Walls 2 feet or longer also require at least one receptacle. For example, an 11-foot-6 wall with a 4-foot door should have one outlet centered 5 feet 9 inches from both the door and the corner.
Use a 1/2-inch drill bit for 12/3 wire and a 3/8-inch bit for 12/2. Drill consistently at 24 inches above the floor for straight runs, lowering to 16 inches near windows. For tight spots like next to windows, use a right-angle drill attachment to maintain precision. Always center the hole in the stud to avoid weakening it.
Staples must be installed within 6 inches of every box and every 4 feet along the wire run. Use 1/2-inch staples for 12/2 wire and 3/4-inch staples for 12/3. Pull the wire taut to the middle of the stud before stapling to ensure a secure and code-compliant installation.
Strip the jacket off both cables entering the box and remove 1/2 inch of insulation from each conductor. Insert both bare copper ground wires into a single copper crimp sleeve, then smash the sleeve with pliers to secure them. Cut one wire shorter, twist both into one solid ground, and push the connection into the box for later device termination.
To bypass doors, drill up into the rafter space and come back down on the opposite side of the doorway. For corners, pre-bend the wire into a 45-degree hook shape to help it snake smoothly around the turn. Always maintain consistent drilling heights and avoid kinks by unspooling wire neatly before running it.
Keep this summary
Save it to LunaNotes and it becomes a real note in your library — editable, searchable, and ready to turn into flashcards or a diagram. Free to start.
Save to LunaNotesOr summarise for another video.
32K+ people have turned 65K+ videos into notes
“Very useful tool. I'm using it for the last couple weeks and I'm loving it so far. Makes learning on YouTube a great experience.”
This summary and transcript were automatically generated using AI with the Free YouTube transcript summary tool by LunaNotes.
Related summaries
How to Wire a Bedroom for Electricity DIY Rough-In Guide
Learn how to wire a bedroom for electricity step by step, including switches, outlets, and a ceiling fan box. This guide covers the 6/12 rule, circuit planning, and code tips for a successful DIY rough-in.
Essential Guidelines for Kitchen Socket Placement
This video provides crucial insights on where to place kitchen sockets, how many to install, and important safety considerations. It covers standard heights, distances from appliances, and design tips to enhance functionality and aesthetics in your kitchen.
Building Codes 101: Zoning, Occupancy Groups & Construction Types Explained
Learn the fundamentals of building design and construction, covering zoning ordinances, building codes (IBC & IRC), occupancy classifications, and construction types. This summary explains how to determine allowable building height, area, and story limits for code-compliant projects.
Engineering Circuit Analysis: Voltage, Current, and Resistance Basics
This foundational lesson explains what an electric circuit is, then dives deep into the core concepts of voltage, current, and resistance using clear analogies like straws and airflow. It also introduces key distinctions between DC and AC, open circuits, short circuits, and the conventional current direction used in engineering.
Building Codes, Sustainability & Construction Standards Explained
This lecture covers the International Building Code (IBC) and International Residential Code (IRC) for construction, focusing on occupancy groups, construction types, and Table 503 for building size limits. It also explores sustainability, the USGBC LEED rating system, and specification documents like the MasterFormat used in construction projects.
Most viewed summaries
A Comprehensive Guide to Using Stable Diffusion Forge UI
Explore the Stable Diffusion Forge UI, customizable settings, models, and more to enhance your image generation experience.
Kolonyalismo at Imperyalismo: Ang Kasaysayan ng Pagsakop sa Pilipinas
Tuklasin ang kasaysayan ng kolonyalismo at imperyalismo sa Pilipinas sa pamamagitan ni Ferdinand Magellan.
Mastering Inpainting with Stable Diffusion: Fix Mistakes and Enhance Your Images
Learn to fix mistakes and enhance images with Stable Diffusion's inpainting features effectively.
Pamamaraan at Patakarang Kolonyal ng mga Espanyol sa Pilipinas
Tuklasin ang mga pamamaraan at patakaran ng mga Espanyol sa Pilipinas, at ang epekto nito sa mga Pilipino.
How to Install and Configure Forge: A New Stable Diffusion Web UI
Learn to install and configure the new Forge web UI for Stable Diffusion, with tips on models and settings.
Found this summary useful?
Take it with you. One click puts it in your own LunaNotes library.
Save to LunaNotes