Overview: Wiring a Bedroom for Rough-In
This guide walks you through the complete rough-in electrical wiring for a bedroom, from planning circuits to mounting boxes and running cable. You'll learn the essential codes and practical methods to wire switches, outlets, and a ceiling fan light combo, all designed for a DIY homeowner building their own house.
What You'll Need: Supply List
- Wire: 12/2 and 12/3 Romex (yellow, for 20A circuits)
- Boxes: 2-gang box (for fan/light switches), single-gang boxes (outlets), saddle box (ceiling fan)
- Staples: 1⁄2-inch for 12/2, 3⁄4-inch for 12/3
- Tools: Drill with 3⁄8" bit, wire cutters, wire strippers, utility knife, hammer, tape measure, level, right-angle drill (for tight spaces)
- Grounding: Copper crimp sleeves, green wire nuts (with center hole)
Key Code Rules for Bedroom Wiring
- Bedroom definition: Must have a closet and an egress window (fire escape).
- Switch placement: A switch must be located right by the door.
- Outlet spacing (6/12 rule):
- Outlet within 6 feet of any corner.
- Outlet within 6 feet of each side of a door.
- Outlets no more than 12 feet apart.
- Smoke detectors: Required inside each bedroom (between door and bed location) and in the hallway outside.
- Circuit amperage: Bedrooms can use 15A (14-gauge wire) or 20A (12-gauge wire). 20A allows more outlets/lights per circuit.
For a more detailed walkthrough of the entire rough-in process, check out Rough-In Electrical in New Construction: Bedroom Wiring A to Z.
Circuit Planning Options
You can wire bedrooms in different ways. Here are two common approaches:
Option 1: Dedicated Circuit per Bedroom
Run a home run from the panel to the bedroom switch box. From there, power flows to both lights and outlets on one breaker. Label the circuit by bedroom (e.g., "Bedroom 1").
Option 2: Shared Circuits for Multiple Bedrooms
- Lights circuit: One home run powers lights in two bedrooms.
- Receptacles circuit: Another home run powers all outlets in those bedrooms.
- This creates two circuits (e.g., "Bedroom 2&3 Lights" and "Bedroom 2&3 Outlets").
Pro tip: For simplicity and troubleshooting, a dedicated circuit per bedroom (Option 1) is often best.
Step-by-Step Rough-In Process
1. Locate and Mount Boxes
- Switch box: Measure 48 inches from rough floor to top of box; mark stud at door entry.
- Outlet boxes: Measure 18 inches from floor to top of box; mark X on stud side.
- Ceiling fan box: Center on ceiling; install saddle box over joist (or add blocking if joist isn't centered).
2. Drill Holes for Wire Runs
- Draw a horizontal line at 24 inches from floor across all studs you'll drill.
- Use a 3⁄8" bit in the center of each stud to avoid drywall screws.
- For windows, drill at 12 inches from the top of the window frame.
3. Run the Wires
- Pull wire from the switch box (power source) to the first outlet.
- String wire through each drilled hole, leaving 6–8 inches of slack at each box.
- Secure wire within 6 inches of each box using the correct staple size.
- For vertical runs, staple every 4 feet max (3 feet is safer).
Example run: Power from switch box → outlet 1 → outlet 2 → ... → last outlet.
4. Install Ceiling Fan Box
- If no ceiling joist aligns with the room center, install a 2x4 block between joists.
- Mount the saddle box over the block using the included screws and lag bolts.
- Run 12/3 wire from the switch box to the fan box (for separate fan and light control).
5. Wire the Smoke Detector
- Install a single-gang box on the ceiling, typically above the bedroom door.
- Run 12/3 wire (or 14/3) to interconnect all smoke detectors so they all sound together.
6. Grounding Methods
Use one of these to tie ground wires together:
Green Wire Nut (with hole)
- Strip outer jacket, cut one ground wire slightly shorter.
- Twist grounds together with pliers.
- Screw on green wire nut over the longest ground wire.
Copper Crimp Sleeve
- Slide sleeve over both ground wires (about 5–6 inches from box).
- Crimp sleeve with pliers.
- Twist wires together and trim one shorter.
Both methods create a single ground pigtail for the outlet.
7. Label Wires and Roll into Boxes
- Label each wire at the switch box (e.g., "Fan/Light," "Power to Outlets," "Home Run").
- Roll all wires neatly inside each box until drywall is installed.
Final Room Overview
- Power source: Home run from panel to switch box.
- Switch box: Powers ceiling fan/light and daisy-chains power to all outlets.
- Outlet circuit: Energizes each outlet around the room.
- TV location: Mid-wall outlet for TV power.
- Ceiling fan/light combo: Controlled by separate switches.
Pro Tips for a Clean Job
- Use a right-angle drill in tight stud spaces.
- Keep wire runs straight and uniform for a professional look.
- Always check local codes, requirements vary.
- Label everything clearly at the panel and switch boxes.
If you have questions, leave them in the comments. For supplies, check the Amazon store linked in the description.
In this video, I'm going to show you how to wire a room for electricity. And in this case, it's the bedroom we're
standing in right now. So, we're going to be going over switches. We're going to be going over outlets. We're going to
be going over a way to mount a ceiling fan, and much more. And if you're new to this channel, my name's Josh. The
channel's all about building your own house, saving a ton of money. So, be sure to subscribe, ring that bell so you
get notification every time I release a new video, and hammer that like button for me. That's all I ask in return for
making this video. So, the first thing I want to do is go over the whole supply list you'll need to do your project. So,
let's get started. Since the bedroom's going to be on a 20 amp circuit, as you can see, we got this yellow wire that is
12 wire. And this is going to be 123 wire, and this is 122 wire. I'll show you what the 123 wire is going to be
used for in just a little bit. And this is going to be a two gang box for a fan switch and a light switch. We got our
single gang box that's going to be for the outlet. So, I got a whole big box of these, and you're going to need
multiples of those depending how big your room is. Then, I got a saddle box to mount the ceiling fan. Then, I got/2
inch wire staples. These are for the 122 wire. Then, I got 3/4 in wire staples, which is for the 123 wire. I got a
drill. Any brand you prefer is fine, but I use Rigid with a 3/8 drill bit on it. And I got a pair of wire cutters. You're
going to need those. A way to mark the height of boxes and switches. A hammer to secure the boxes and switches and to
drive the staples. A tape measure and your tool bag. That's what you'll need for rough in. After we rough the wires
in, I'm going to tie the grounds together using these copper crimp sleeves and these twiston wire
connectors with the little hole in the middle to tie the grounds together. I'll show you how to use all this in just a
bit. And these wire strippers and utility knife are going to be needed for that as well. So, I want to go over some
rules before we get started wiring. Before I go over bedroom wiring, I wanted to disclose that I am not an
electrician, but I have wired four houses on my own, and they have all passed inspection with no problem. So,
with that being said, this is just for entertainment purposes only. So, the rules that I came up with through all my
experience wiring my own houses is you must first distinguish the difference between a bedroom versus other rooms.
So, in order for a room to be considered a bedroom, it must have a closet and it must have a egress for a fire escape.
So, a window that's opening up to a certain size that meets your egress requirement. That is what accommodates
for a bedroom. So, just real quick again, has a closet and has egress to escape from a fire. And check with your
local building codes to see what needs to be put in place for your bedrooms to pass code. And with that being said, you
must have a switch by the door once you enter the room. So that's pretty common sense. I think most people can uh say
they would want a switch when they open up their bedroom door to turn the light on, but just want to put that out there.
So you must have a switch right by your door. And the outlets that you install in the bedroom must follow the 612 rule.
So what the 612 rule is, I made a detailed video a while back. You can check out the link up here to go to if
you want to see it, but I made the detailed version of the 612 rule on that video. But more or less says you got to
have an outlet within six foot from a corner and within 6t from each side of a door. And your outlets can't be any
farther than 12 foot apart. So that's why it's called the 612 rule. And there's some more details to it, but go
watch that video if you want to see all the details. But that's just the gist of it. So all your outlets must follow
those rules. And the smoke detectors must be placed in each bedroom and it has to be placed in the hallway where
the bedroom enters into. So you got to have a smoke detector in the actual bedroom from between the door and the
where the bed's going to be. There has to be a smoke detector there and it has to be a smoke detector right outside in
the hallway, too. So just something to keep in mind. Again, check your local building codes to see what they
recommend, but that's how it is here. And you can wire the bedroom on either a 15 amp circuit or a 20 amp circuit. So
places like the bathroom and kitchen, they have to be on 20 amp circuits using the 12 wire, which I just showed you
earlier. So bedrooms can be wired using 14 wire, but you can only have a 15 amp circuit in that case. So it limits the
amount of outlets and lights you can put on that. So just keep that in mind. And I want to show you a certain way you can
wire multiple bedrooms and uh versus just one bedroom. so you can pick which one would work best for you. When it
comes to breaking up bedrooms into different circuits, I'm going to show you two common ways you can do that. So,
this is the way I like to put a bedroom on a circuit is right here. And this is very simple to understand. All you got
to do is run a home run straight from your panel box to a bedroom. I prefer to go to the light switch because there you
can break the power out from the light switch and go to the outlets. And there you can power your lights and
receptacles all off one circuit. So you would label this bedroom one for instance in the panel box. So you know
when you kick that breaker it shuts all the power off to bedroom one. So over here on bedroom two and three we could
we're going to do it a little different here. I usually don't do it like this but I'm going to show you how you can.
So, if you look here, we got a home run coming from the panel box over to the light switch just for the lights in
bedroom three and bedroom two. So, the power is coming over here to a switch. Then, that power breaks over to this
room, too. So, you can operate these lights off this switch and these lights off this switch, but it's just one power
coming from the panel box. And then you you're probably wondering, well, what powers these outlets? So, what you would
do is you would make a home run straight to your outlet to any one of the rooms. And then you go from outlet to outlet.
And then you can go over here to outlet to outlet. And then we'll call this circuit bedroom. And sorry, my
handwriting isn't the best. Bedroom two and three. You can call it outlets or receptacles. I mean, it's whatever you
want to call it. They're the same thing. So this could be three different circuits here and they all achieve about
the same thing. So if we kick this breaker, we kill the lights going to both of these bedrooms. If we kick this
breaker, we kill the outlets in both of these bedrooms. Or you could simply do what you did on bedroom one, and you
could have made a home run here, powered that whole bedroom, a home run here to power this whole bedroom. So it's really
in what you prefer. And on 20 amp circuits, you can put a lot of receptacles and lights compared to 15
amp circuits. So depends on what amperage circuit you're doing is what this might be more suitable for a 20 amp
circuit versus a 15. So that's however you want to do it. But I just want to show you some examples when it comes to
taking the home run right to the panel box and breaking bedrooms up in circuits. So the first thing I do when
it comes to wiring a bedroom, I'll locate where the switch is going to be on the wall when you open up the door.
So in this case, this is the doorway. So, the door is going to swing towards this wall over here because there's
going to be a couch right where the camera is sitting. So, I know I'm going to want to come up 4 foot to the top of
the switch. So, I'm going to go ahead off the rough floor, measure up 4 foot and put a mark. All right. And now that
that's marked, all you got to do now is take the box and as you can see here, see these little flanges right here and
here? that's going to go up against the stud. So, you just take it, slide against the stud because that's going to
give us a half inch for our drywall. So, the box is going to be flush after the drywall is hung. So, you hold it tight
in into position and just tack these nails in from the top and bottom. It's going to secure it where it goes.
Right here is the box we just anchored. And that's an important thing to note because that's where the power is going
to be coming from for our outlets. And right here is the side of the door opening that we got to be at least six
foot from. So as far as the first outlet goes, what I like to do is just pull off that door opening and see where that
puts me. So right here is 3T, which is plenty within range of that door. And then I'm going to measure up 18 in off
the floor. And that's going to be the top of our box. And I always put an X on the side of the stud where the outlet's
going to be located. So I'm going to put a X on the side of the stud here. And I know my outlet box is going to be
sitting right here. So I'm going to go around the whole room and lay out what I need and go from there.
[Music] [Applause] [Music]
Now that we got them all laid out, we just go through and drop a box in front of each one of those studs we marked.
And that way we can go through and nail them all up at the same time. Now that we got the boxes laid about
where they go, we go through and start securing them to the studs where we marked earlier. So right here is our
18inch mark, which is the top of the box. Here's the X. So that tells us the side of the stud the box is going. So
this side has the flanges on the outlet box. So it spaces us correctly away from the end of the stud for drywall. So we
line it up to that mark. And then you just drive these nails in the top and the bottom till they're tight against
the box. And that's how you install the outlet box. So go to each spot that has an outlet
and do that. [Music] [Applause]
[Music] [Applause] [Music]
[Applause] [Music] So, another cool trick that I had a
subscriber mention in my last electrical video is they'll take their hammer and it's a certain hammer they use for every
electrical job and they'll just slide their outlet down to the top of that hammer and that is how they get the
height for all their boxes. Now, I don't have a hammer that suits my needs for that, but thought it was a cool tip.
Thanks a lot, subscriber if you're watching. So, what I like to do before I start drilling holes to run the wires, I
like to measure up two foot off the floor. So, that way it gives me a nice guide to go by when I'm drilling through
the studs. So, it keeps your wires looking good going through the wall so they're not all spaced evenly off the
floor. So, it gives you a good clean job. So, I'm just going to do that to each stud I'm going to be drilling
through. And if you want to, you can use some kind of laser level to put a line on it. Or you could take a block that's
two foot set on the floor. forcing to use your tape measure, but I just been using my tape measure for the most part.
It's just convenient that way. Here's our twoft mark. Now, take a drill with that 3/8 drill bit on it and go in
the center of the stud. You don't want to be way out here. You don't want to be way back here. Want to be right in the
center so drywall screws don't hit the wire. And just drill right through it. [Music]
And now do that to each one of those studs to where you know the path of your wire is going to be.
[Music] [Applause] [Music]
[Applause] [Music] [Applause]
When I get here to a window, I measure up 12 in and make a mark because you cannot use 24 anymore if the window's
too long. And 12 in is good because our box is sitting here. So, it gives us room to staple underneath the box.
Whenever you get to a spot like this where your regular drill can't get in very well, what I use is a right angled
drill. And this is just a rigid Job Max with a right angle head attachment. So, this way you can just squeeze it right
in between the studs and go to town. [Music] I just like to take a moment and for you
to take note that these outlets are closer than what the code calls for, but it's definitely more functional to have
those outlets every 6 ft apart than having that 12t space in between, which that's definitely going to be a selling
point as well. So, with this run right here, the next outlet is over here. here. And as you can see, we got this
closet door in the way. So, what we got to do, we're going to have to drill up through the double plating into the
attic space and then come down in this open in this space here between these studs to meet this outlet. And then,
it's kind of a unique situation. I got this duck in the way here. So, I'm going to have to go back up through to go and
bunny hop over into this stud space. Then I'm going to hit this outlet that's mid wall for a TV that I'm going to
install here to go to this outlet, then finish a run that way. Kind of a weird situation here, but you will run into
those in construction. [Music] So, in order to start running the wire,
we know the power is going to be coming from this switch box when I eventually run the home run to the panel box. So,
with that being said, it's going to come down this stud and go through the holes I drilled into the outlet box. So, what
I like to do, I like to take the roll wire and just unravel it a little bit in these short runs just so I can get some
started without it being all wrapped up and hard to work with. And then you simply just fish it through the holes
you drilled and then take it up to the box you're headed to. And then I'm going to show you how to secure it and how
much leave out of the box. So, what I like to do first is take a pair of needlense to push these little tabs in
the back of these boxes out, as you can see in the back, cuz they're seized together when you first get them. So,
then all you got to do is take your wire and fish it through one of those ports, and it should slide in fairly easy. And
what you need to do is make sure you leave enough out of the box to meet code. There has to be at least 6 in left
out. So, a lot of times I'll leave a little more than that. As you can see, there's probably a good seven or eight
inches. Once you got the correct amount of wire sticking out of the box, then I'll take a 1/2 in staple for this 122
wire and go ahead and hold it in the middle of the stud. And then bracket that wire using the wire staple and stay
within 6 in of this box. You can't be further away than that when it comes to stapling per code. Then just just go
ahead and secure that wire into place. All right. So now that wire is secured and not going anywhere. So now at the
other box that you had to roll wire beside that you started out at, I go ahead and wrap it behind the back of the
outlet box. Hold about 6 to 8 in of wire and then snip it. And then I know I'll have plenty of wire in this case. And
then I jab the back of the outlet box out and then slide that wire through. And then go ahead and press it kind of
in the middle of the stud to hold in place. And then I'll go ahead and take that roll of wire, unravel it, and go to
the next outlet box and run it this way. And then do the same process over and over again till you're done the room.
All right. Like I said, go ahead and unroll part of the roll just like we did a second ago. and then fish it through
to get to that outlet box. And now I'll show you how to secure this wire inside of this outlet box next. So,
similar to the switch box, same thing. Just slide the wire in and make sure you pull enough to allow to have about 6 to
8 in hanging out of the box. And then press this against the wire that's coming from the switch like that. And
now these wire staples can hold two wires comfortably. So now go ahead and just secure that into place.
And then after that, all I do next is roll that up into the box. And then we'll tie all these together once the
drywall is done. And again, to be clear, we need to keep this wire staple below 6 in. It has to be within this area or it
does not pass code in my area. [Music] [Applause]
[Music] [Applause] [Music]
[Applause] [Music] You may remember in the beginning of
this video I mentioned each bedroom needs a smoke detector in it to pass code. So in order to do that you need to
put a single gang box somewhere between the door and where the bed's going to be. I usually put it in the ceiling
right directly above the door when you enter the room. But you need to run a three wire whether it's 143 or 123 to
each smoke detector. So they're all hardwired together. So, if one alarm's a all alarm. And if you know how to do
that, I made a video a while back and the link to it is in the top right hand corner of this screen. Go check it out
and let me know what you think. [Music] [Applause]
[Music] [Applause] [Music]
[Applause] [Music] Whenever you have a wire running up the
side of a stud like you see here, you need to be sure to take a wire staple and staple it every 4T apart or closer.
But it can't be any further apart than 4 foot. I usually go about 3T or so. It seems to hold the wire a little better.
But that's just something you need to do when you're wiring your room. [Music]
[Applause] [Music] [Applause]
[Music] As you can see, I got all the outlets ran around the room and all the wires
ran to each one of the outlets. So, now what I want to do is take these two outlets that you see the wires hanging
out of and wire the grounds together. And I'm going to show you some methods to do so. I'm going to show you how to
wire the grounds together using these twiston wire connectors. They have a hole right in the center. They're
designed for grounds to be tied together. You can find these in my Amazon store in the description below.
If you order them through my Amazon store, I do get a small commission, but it's at no extra cost to you. So, the
first thing I'm going to do is strip the coating off this wire. And all I do is just lightly graze across the jacket
just enough to score it. You don't want to push hard and cut into the wire. And then that's just going to give you a
place you can start stripping the casing back on. All right.
So I get all the paper, everything off the wire. And you don't want to cut towards the wire. Be sure to cut away
from the wire. That's a common practice. And then do the same thing to the other one to slightly graze across it. And
again, don't push hard. And now you just pull that jacket back. Right. Like so. And make sure you get
all the paper off the copper and everything. And again, cut away from the wire. Don't cut towards the wire. And
now you're going to have two blacks, two whites, and two grounds. I'm just going to take these wire strippers and strip
these wires. And you can find these wire strippers in my Amazon store. And go ahead and strip off about 38 of an inch.
And this is just going to get you ready for when you actually hook up your outlet.
But um I just wanted to show you how to do it. You don't have to do this right now. You can do this after the drywalls
hung. But just for demonstration purposes, I'm going to show you how that worked. So now what I do, I push my
insulated wires over to the side. Now I'm just working with these copper wires. And what I'm going to do is cut
one of these a little shorter than the other one. And it doesn't have to be way back here. You definitely don't do that.
Now, you want to leave eh a good five, six inches at least left on there. And I'm talking about from inside where the
wire is out. So we'll go ahead and snip that back a little bit. And now what I do is I go ahead and
twist these together. And this is um it's pretty simple to do. Just take your pair of wire pliers and
just keep twisting. And you want to get a nice even twist here. And uh you don't want to over twist it to where it breaks
the wire. Just something pretty comfortable. You're more or less just turning this ground wire into one ground
wire. All right. So, now that we got that twisted together, we just take our green wire nut, slide it over the end of
the one longest ground wire, and then where they both meet, you just go ahead and twist that on to where it binds both
of these together. And if you had more than just two grounds, you just twist them all. And as you can see, that gives
you one solid ground wire. And then this would hook onto your receptacle. And then these would as well. And that is
all there is to that. And now we're not going to wire these to the outlet until the drywall is hung. So we're just going
to roll these back into the box. And that's all there is to using the green wire nut. I'm going to show you another
method using a crimp sleeve. So now I prepared another outlet box. And I'm going to use what's called copper crimp
sleeves. And these work really easy as well. So all you got to do is take your two grounds in this case. Slide your
copper crimp sleeve over the grounds. Come down to your about again five six inches away from the head of the box
there. And then clamp that crimp sleeve down. And that's just going to kind of smash over the copper wire. And then
just go ahead and twist it similar how we did the last one, except this case we have a co the copper crimp sleeve
holding them together. Again, twist it comfortably, not super hard. And then here, I just take one of the shorter
ones and then just snip it a little shorter than the other one. And again, make sure it's long enough in case you
had to undo this to jump an outlet out of this box or something that there's enough wire to do so. And as you can see
here, it does a similar job to what the wire nut does. It's just connected a little different, but it's a nice clean
job. And now we're again going to roll these up, put them in the outlet box, and we will install the outlets in a
later video after the drywalls hung. Now it's time to address the lighting in the room. So for lighting, I'm going to
mount a ceiling fan light combo. So in order to do so, I'm going to install this ceiling fan box. This is called a
saddle box. And it's called a saddle box because of the design. And as you can see there, has like a U shape out of it.
And what that does is go over your ceiling joist or rafter and that's going to hold the weight of the ceiling fan.
And sometimes you got to put a block between ceiling joistices in order to hold the ceiling fan because it doesn't
hit directly in the center of the room. And that's what you want to do. You want to hang the fan right in the center of
the room, of course. So, we're going to go ahead and do that. And just so you know, you can find these in my Amazon
store as well. All right, let's go measure to see if we need a block or not. So, there's a little screw right
here. Pop that out. and we're going to use that to mount it to the block. As you can see, I did not get lucky and the
center of the room was actually right here and there was not a ceiling joist or rafter or truss to anchor it to. So,
I had to put this block in. Nine times out of 10, you'll have to put a block in when you're using this method. So, just
go ahead and slide your saddle box right on your mark that you made. Right, like that. And then all you got to do is
install that little screw back into that hole. And that's just going to hold it right in place until the drywall's hung.
And there's these lag bolts that they that came with the box. These lag bolts will anchor the ceiling fan bracket. And
that's what ultimately holds the weight of your ceiling fan. Now, let's get this sucker wired up. So ultimately what we
got to do is run a 123 wire up to that ceiling fan box from down here to where the switch box is to where the power is
going to be coming in at. [Music] Now we need to put this 123 wire into
that saddle box. So we're just going to fish at least 6 to 8 in and that should be plenty there. And then we're going to
roll it up into the saddle box until the drywall is hung. And now to staple this, we need to use a 3/4 in wire staple
because the 123 wire is a little wider that little wider than the 122 wire. So let's go ahead and get this flattened
out on the stud. That looks pretty good. Something like that. And now we're just going to secure it
within 6 in of that box, just like all the other boxes. All right, that looks good. All right, let's go address the
switch side. All right, we got the 123 wire ran up to the ceiling fan light combo. Now I need to make a home run
with 122 wire from this switch box to the panel box. So I'm going to do that now.
[Music] [Music] All right. So, this is the end of that
run. We're going to label this bedroom four. So, once we have a bunch of these home runs to the panel box, we know
exactly what they're for. and leave plenty of length here because we got a wire into this. So, you don't know how
much exactly you'll need. And don't yell at me for having the cover off because it is not connected to the power grid
yet. And be sure to subscribe because I'll be making a detailed video on how to wire a panel box. All right, let's go
back to the switch box to show you what to do next. All right, now we need to get the rough length here. Again, pull
it out of the box about 8 in. And we're going to go and cut that. And now we just got to fish it through the hole we
drilled earlier. And it's going to take the 123 wire with the 122 wire for the power through the same hole.
Okay, that looks good. So now what we need to do is staple these to the stud right here for code.
All right, we want to make sure we flatten these wires out and that they look nice and uniform. You don't want to
make a rough looking job. The inspector doesn't like that either. So, within 6 in from the box, put a wire staple. And
we got to use the 3/4 staple because of the 123 wire. Now, while everything's fresh in our
minds, we're going to label these. The 123 wire is a given, but we'll put fan light combo.
And I'll know what that is for. And then this one that's going down to the outlets, that's going to be our power
continued. So power, then I'll put co n t with a dot. And then this one we know is the
power. So, when it just says power, I'll know it's coming for um to energize this circuit here. Okay. So, that's all there
is to labeling that. And now I'm just going to roll all these up into the box and I will be able to finish wiring
these once the drywall is installed. So, one quick overview. So, the power is coming to this box and it's going to
power the fan and light. And the power is going to continue and energize all these receptacles all the way around the
room. And then we're going to get right here and this is going to be to power our receivers for our TV. And this is
where the TV is going to hang. And then it's going to energize this last receptacle here. And then to light up
the room, we got the ceiling fan and the light combo up here. If you have any questions about this project, be sure to
ask them in the comment section below. I'll get to them as soon as possible. And if you've seen anything in this
video you'd like to purchase, such as the supplies to wire these outlets, be sure to check out my Amazon store. The
link is in the description below. I do get a small commission, but it helps support the channel. And again, my
name's Josh. The channel's all about building your own house, a ton of money, be sure to subscribe, ring that bell,
and hit that like button for me. All right, guys. I'll see you in the next video. Have a good one. Thanks for
watching.
The 6/12 rule states that an outlet must be within 6 feet of any corner and within 6 feet of each side of a door. Additionally, outlets should be no more than 12 feet apart along any wall space. This ensures convenient access to power and compliance with electrical codes.
A dedicated circuit runs one home run from the panel to a single bedroom, powering both lights and outlets on one breaker, which simplifies troubleshooting. A shared circuit uses separate home runs for lights and outlets, potentially covering multiple bedrooms, which can reduce material costs but may complicate future repairs. For ease and simplicity, a dedicated circuit per bedroom is often recommended.
For the switch box, measure 48 inches from the rough floor to the top of the box and mount it at the door entry. For outlet boxes, measure 18 inches from the floor to the top of the box and mark the stud side. For a ceiling fan, center the saddle box over a joist or add a 2x4 block between joists if needed, then secure the box with the provided screws and lag bolts.
For a 20-amp circuit, use 12-gauge wire, specifically 12/2 Romex for standard outlets and lights, and 12/3 Romex when you need separate control for a ceiling fan and light. The yellow jacket on 12-gauge wire distinguishes it from 14-gauge wire used for 15-amp circuits.
Drill holes at 24 inches from the floor through each stud using a 3/8-inch bit to avoid drywall screws. Pull wire through the holes, leaving 6–8 inches of slack at each box. Secure the wire within 6 inches of each box using the correct staple size (1/2-inch for 12/2, 3/4-inch for 12/3), and for vertical runs, staple every 4 feet maximum (3 feet is safer).
The two methods are the green wire nut with a center hole and the copper crimp sleeve. For the green wire nut, strip the outer jacket, cut one ground wire shorter, twist all grounds together with pliers, and screw the nut over the longest wire. For the crimp sleeve, slide the sleeve over both wires 5–6 inches from the box, crimp it with pliers, then twist the wires together and trim one shorter. Both create a single ground pigtail for the outlet.
Install the smoke detector on the ceiling, typically above the bedroom door. Use 12/3 wire (or 14/3 for 15-amp circuits) to interconnect all smoke detectors so they all sound together. This placement ensures the detector is between the door and the bed location for optimal safety.
Keep this summary
Save it to LunaNotes and it becomes a real note in your library — editable, searchable, and ready to turn into flashcards or a diagram. Free to start.
Save to LunaNotesOr summarise for another video.
32K+ people have turned 65K+ videos into notes
“Very useful tool. I'm using it for the last couple weeks and I'm loving it so far. Makes learning on YouTube a great experience.”
This summary and transcript were automatically generated using AI with the Free YouTube transcript summary tool by LunaNotes.
Related summaries
Rough-In Electrical in New Construction: Bedroom Wiring A to Z
Learn how to rough-in electrical for a new construction bedroom, from installing switch boxes and ceiling fan mounts to running 12/2 and 12/3 Romex. This guide covers the 6/12 rule for outlet spacing, proper stapling techniques, and tips for wiring receptacles and lights on separate circuits.
Engineering Circuit Analysis: Voltage, Current, and Resistance Basics
This foundational lesson explains what an electric circuit is, then dives deep into the core concepts of voltage, current, and resistance using clear analogies like straws and airflow. It also introduces key distinctions between DC and AC, open circuits, short circuits, and the conventional current direction used in engineering.
Essential Guidelines for Kitchen Socket Placement
This video provides crucial insights on where to place kitchen sockets, how many to install, and important safety considerations. It covers standard heights, distances from appliances, and design tips to enhance functionality and aesthetics in your kitchen.
Building Codes 101: Zoning, Occupancy Groups & Construction Types Explained
Learn the fundamentals of building design and construction, covering zoning ordinances, building codes (IBC & IRC), occupancy classifications, and construction types. This summary explains how to determine allowable building height, area, and story limits for code-compliant projects.
Complete Guide to Series, Parallel, and Combined Electrical Circuits
This detailed lesson explains the fundamentals of electrical circuits, covering series circuits, parallel circuits, and combined series-parallel configurations. Learn key principles such as voltage distribution, current flow, and essential formulas to analyze complex circuits effectively.
Most viewed summaries
A Comprehensive Guide to Using Stable Diffusion Forge UI
Explore the Stable Diffusion Forge UI, customizable settings, models, and more to enhance your image generation experience.
Kolonyalismo at Imperyalismo: Ang Kasaysayan ng Pagsakop sa Pilipinas
Tuklasin ang kasaysayan ng kolonyalismo at imperyalismo sa Pilipinas sa pamamagitan ni Ferdinand Magellan.
Mastering Inpainting with Stable Diffusion: Fix Mistakes and Enhance Your Images
Learn to fix mistakes and enhance images with Stable Diffusion's inpainting features effectively.
Pamamaraan at Patakarang Kolonyal ng mga Espanyol sa Pilipinas
Tuklasin ang mga pamamaraan at patakaran ng mga Espanyol sa Pilipinas, at ang epekto nito sa mga Pilipino.
How to Install and Configure Forge: A New Stable Diffusion Web UI
Learn to install and configure the new Forge web UI for Stable Diffusion, with tips on models and settings.
Found this summary useful?
Take it with you. One click puts it in your own LunaNotes library.
Save to LunaNotes